- #GM340 PROGRAMMING SOFTWARE SERIAL#
- #GM340 PROGRAMMING SOFTWARE DRIVER#
- #GM340 PROGRAMMING SOFTWARE MANUAL#
- #GM340 PROGRAMMING SOFTWARE FULL#
- #GM340 PROGRAMMING SOFTWARE SOFTWARE#
The signal routed to this pin is controlled by ASFIC and gives continuous discriminator audio. Resistor R0423, 4.7 kohm, which is not fitted as standard will cause the radio to be permanently on whenever 12 V is connected to the main power connector.
#GM340 PROGRAMMING SOFTWARE MANUAL#
When this line is at 0V or is not connected, power on/off is under manual control. When the ignition is connected, the radio cannot be turned off as long as the ignition is active. Connecting this line to the ignition line of the vehicle will automatically turn the radio on when the ignition of the vehicle is turned on. This can be used for any input function, but is usually used for emergency. This is a special input that will force the radio to turn on when it is grounded. The RSS details which functions may be assigned to this pin by the codeplug. To restore general purpose output operation, the programming lead must be removed and the radio turned off, then on again.
#GM340 PROGRAMMING SOFTWARE SERIAL#
It can be used as a normal output, but will be overridden by serial data when the programming lead is plugged in. This output is shared with the serial bus data line. This is a digital output and is also available on the internal option connector (J0103:7). Used as a ground for both analog and digital signals. This line is also available at the microphone connector Pin 7. This connects to the radio's SCI serial bus which is used for programming and tuning the radio. The nominal input level is 150 mVRMS for 60% deviation. This input is for injecting signals into the transmit path that should not be filtered, e.g. The primary use for this pin is as external alarm output. The RSS details whuch functions may be assigned to this pin by the codeplug. The primary use for this pin will be external PTT. This is a digital input only and is also available on the internal option connector (J0102:7). Note: Only one microphone should be connected at any one time. The DC impedence is 1100 ohms and the AC impedence is 1000 ohms. The nominal input level is 80mV for 60% deviation. This microphone signal input is common with the microphone singal input on the microphone connector and is connected to the microphone path input of the ASFIC. Disconnect the internal speaker and assemble the control head back to the radio. The internal speaker can be easily disabled by removing the control head. The audio PA is a bridge amplifier with a minimum load resistance of 3.2 ohms. Speaker- and Speaker+ (PIN 16) are used to connect an external speaker. The 16-pin accessory connector pin functions for the GM950 N3/N4 are as follows: Pin You plug this cable on the end of the standard programming cable (RJ45) and then into the accessory plug on the radio for rear programming (in the event you don't have a head on the radio to program through the mic jack). It is an RJ45 female that is wired to a 16pin accessory connector using the above schematic. The above cable lets you program from the accessory connector instead of the mic connector. If you are looking for the the pinout of the GTF377A "Front to Back" cable, the pinout is:
#GM340 PROGRAMMING SOFTWARE FULL#
It comes in 4 flavours, 4 channels w/o LCD, 128 ch with LCD, 128ch with handheld control mic (HHCM), and 128ch with full keypad (eg. They have similar features to GM350 but also have SELECT-5. Out of band is similar to the GP320/340 series. They come in two flavours, 4 channels without LCD and 128ch with LCD. The GM350 has its own RSS and are a PL/Singletone only version of the GM950.
The MCX600 is the Asia version of the GM600 which is the MPT version of the GM350/950. If there are any significant differences, please email us. These radios should all be similar to each other.
#GM340 PROGRAMMING SOFTWARE SOFTWARE#
The software will have to be obtained separately.GM350, GM600, GM950, MCX600 Mobiles GM350/GM600/GM950/MCX600 Mobiles Note: This cable does not include any software. Our universal analogue motorola two-way radio programming cable is actually 5 cables in 1.
#GM340 PROGRAMMING SOFTWARE DRIVER#
This means much less likely to "brick" your radio.ĭrivers: You can download the driver for this cable here.
The FTDI chipset does not typically suffer from the issues associated with other chipsets. Other chipsets including Prolific and CP200 etc. This cable uses the FTDI chipset which has been proven to work with Motorola analogue radios. We have started a Facebook group to hopefully support owners of the now discontinued Motorola GP340/HT750 series radios: Proven To Work Chipset